local device = {}
device.model = "TS0601_smart_temperature_switch"
device.vendor = "Tuya"
device.description = "Smart temperature switch with manual and automatic modes: heating & cooling"

device.exposes = {
        {
            type = "numeric",
            name = "temperature_c",
            property = "temperature_c",
            access = 1,
            unit = "℃",
            description = "Measured temperature in ℃. Device reports it only when it set ℃ unit.",
            category = "diagnostic",
        },
        {
            type = "numeric",
            name = "temperature_f",
            property = "temperature_f",
            access = 1,
            unit = "℉",
            description = "Measured temperature in ℉",
            category = "diagnostic",
        },
        {
            type = "switch",
            description = "Turn on/off device connected to output",
            features = {
                {
                    type = "binary",
                    name = "state",
                    property = "state",
                    access = 7,
                    value_on = "ON",
                    value_off = "OFF",
                    description = "On/off state of the switch",
                },
            },
        },
        {
            type = "binary",
            name = "autowork",
            property = "autowork",
            access = 7,
            value_on = "ON",
            value_off = "OFF",
            description = "Turn on automatic mode to control constant temperature",
            category = "config",
        },
        {
            type = "enum",
            name = "work_mode",
            property = "work_mode",
            access = 7,
            description = "\n                Heating: switch is turned ON until temperature will increase to setpoint (then will turn OFF). When temperature will go down below set temperature range, switch will turn ON again.\n                Cooling: switch is turned ON until temperature will decrease to setpoint (then will turn OFF). When temperature will go up above set temperature range, switch will turn ON again.\n            ",
            category = "config",
            values = { "heating", "cooling" },
        },
        {
            type = "enum",
            name = "temperature_unit",
            property = "temperature_unit",
            access = 7,
            description = "Temperature unit",
            category = "config",
            values = { "celsius", "fahrenheit" },
        },
        {
            type = "numeric",
            name = "temperature_c_setpoint",
            property = "temperature_c_setpoint",
            access = 7,
            unit = "℃",
            min = -20,
            max = 102,
            value_step = 0.5,
            description = "Temperature ℃ set point",
            category = "config",
        },
        {
            type = "numeric",
            name = "temperature_f_setpoint",
            property = "temperature_f_setpoint",
            access = 7,
            unit = "℉",
            min = -4,
            max = 221,
            value_step = 0.5,
            description = "Temperature ℉ set point",
            category = "config",
        },
        {
            type = "numeric",
            name = "temperature_range",
            property = "temperature_range",
            access = 7,
            min = 1,
            max = 9,
            value_step = 0.5,
            description = "The delta between temperature setpoint and measured temperature to trigger heating or cooling",
            category = "config",
        },
        {
            type = "numeric",
            name = "temperature_calibration",
            property = "temperature_calibration",
            access = 3,
            unit = "℉",
            min = -9,
            max = 9,
            value_step = 1,
            description = "Temperature calibration always in ℉",
            category = "config",
        },
        {
            type = "binary",
            name = "cooling_delay_switch",
            property = "cooling_delay_switch",
            access = 7,
            value_on = "ON",
            value_off = "OFF",
            description = "Turn on cooling mode delay",
            category = "config",
        },
        {
            type = "numeric",
            name = "cooling_delay",
            property = "cooling_delay",
            access = 7,
            unit = "m",
            min = 0,
            max = 10,
            value_step = 1,
            description = "Delay to turn on - only for cooling mode",
            category = "config",
        },
        {
            type = "numeric",
            name = "countdown",
            property = "countdown",
            access = 7,
            unit = "s",
            min = 0,
            max = 86400,
            value_step = 1,
            description = "Countdown to turn device on/off after a certain time",
            category = "config",
        },
        {
            type = "list",
            name = "schedules",
            property = "schedules",
            access = 2,
            description = "Schedules for automatic mode work at certain week day and time",
            category = "config",
        },
    }

device.tuyaDatapoints = {
    { dp = 2, name = "state", converter = "onOffNotStrict" },
    { dp = 4, name = "countdown", converter = "countdown" },
    { dp = 7, name = "schedules", converter = "thermostatSchedule" },
    { dp = 8, name = "work_mode", converter = "lookup",
        lookup = { heating = 0, cooling = 2 } },
    { dp = 9, name = "autowork", converter = "onOffNotStrict" },
    { dp = 20, name = "temperature_unit", converter = "temperatureUnitEnum" },
    { dp = 21, name = "temperature_f_setpoint", converter = "divideBy10" },
    { dp = 22, name = "temperature_c_setpoint", converter = "divideBy10" },
    { dp = 27, name = "temperature_c", converter = "divideBy10" },
    { dp = 28, name = "temperature_f", converter = "divideBy10" },
    { dp = 29, name = "temperature_range", converter = "divideBy10" },
    { dp = 30, name = "temperature_calibration", converter = "raw" },
    { dp = 55, name = "cooling_delay", converter = "raw" },
    { dp = 56, name = "cooling_delay_switch", converter = "onOffNotStrict" },
}

device.fingerprint = {
    {
        model = "TS0601",
        manufacturer = "_TZE284_roujjevx",
    },
}

return device